Morimoto 4Banger Fog Light Install: 2015-2019 Silverado HD

Morimoto 4Banger fog light kit intro for 2015-2019 Silverado HD

Replacing dim factory fog lights with higher output lights makes an easy upgrade. The Morimoto Banger delivers serious light output.

We installed a Morimoto 4Banger fog light setup on a Silverado HD in our shop. This guide covers everything we learned. We detail two available chip levels and various beam patterns. We also list the exact tools you will need for the job.

The Bangers rank among the brightest pod lights available today. Installation stays straightforward once you understand how the brackets assemble.

What the Morimoto 4Banger Is All About

Before we grabbed a single tool, we wanted to explain what makes the 4Banger tick. The lineup comes in two different versions. The entry level version uses a Nichia chip, which we call the NCS version. The premium version targets off roaders and anyone who wants maximum output from their pod lights. It uses an Osram chip, which we call the HXB or HX Boost. Both versions share the same housing and installation process. Your choice comes down to the output you want and how you plan to use your truck.

Once you have decided which application level you want, the next decision is the driving pattern. We tested all three, and each one has a purpose depending on how you drive and where you drive.

Three Beam Patterns, Two Colors

There are three patterns to choose from: spot, wide, and combo. All three are available in either white or amber, so you have real flexibility no matter which chip level you pick. The wide pattern is the one most people gravitate toward because it helps increase night visibility and works so well as a fog light replacement. No matter if you choose the NCS or the HX Boost, the wide pattern produces the same driving beam pattern, so you get consistent performance across both tiers.

The 4Banger comes in spot, wide, and combo beam patterns, each available in white or amber.

The combo beam pattern is a super cool spot beam with a little bit more fill. It stacks up to the competition very well, though most people still lean toward the wide pattern over something like this. The spot beam pattern is an incredibly bright, tight beam that actually looks like a square. That shape is done on purpose because at Morimoto we know a thing or two about beam patterns. If you want the wide version specifically, you can grab the Morimoto 4Banger NCS Wide Beam LED pod for the entry level route or step up to the Morimoto 4Banger HXB Wide Beam LED pod for the premium Osram build.

The Truth About Amber and Brightness

Color choice matters here, and there is a real difference between the two chip levels when you go amber. On the higher end, the HXB uses the Osram chip, but it does not come in a yellow version. That means the white light has to pass through the yellow lens, and it loses about 30 percent of its brightness. It is still an incredible option, but you should know that going in. The entry level NCS is different in a neat way: those Nichia chips do come in a yellow option. Having a yellow light pass through a yellow lens means it does not lose nearly as much brightness, so the output stays closely matched to the white counterpart. If amber is a priority for you, the NCS yellow chip is worth serious consideration.

Footprint, Fitment, and Street Legal Status

One of the reasons the 4Banger fits so many trucks is its size. The overall footprint is approximately 30 percent smaller than alternatives that offer comparable performance. That compact design allows for an unbeatable 30mm plus fitment when paired with Morimoto’s fog light or A-pillar mounting kits. With a standard and negative three degree aim, the beam pattern produced by the NCS wide beam model is designed to be compliant with the latest SAE F3 regulations for use as a street legal fog light. The HXB wide beam is designed to meet those same SAE F3 regulations, so both wide beam versions are built to be street legal. On top of that, the 4Bangers are backed by a limited lifetime warranty, which is exactly what you want on a pod light you plan to run for years.

If you are comparing options across the Silverado platform, it is worth checking out the Silverado 2500HD Morimoto XB LED fog lights at Headlight Revolution and the Chevrolet 4Banger round fog light kit at The Retrofit Source to see how the kits differ by fitment and bracket style.

Building the 4Banger Bracket

With the product overview out of the way, we headed to the table to build out the bracketry before touching the truck. Whether you are pulling a factory fog light or an aftermarket unit, the process starts the same way. First, you take off the adjustment piece on your factory fog light. There are two little screws on the side, and if it is too tight to remove, you just loosen those two Phillips screws. In our case it was already pretty loose, so we simply popped that little piece out.

Building out the pre-assembled Morimoto bracket before mounting the 4Banger pod light.

Next, grab your Morimoto fog light bracket. These come pre-assembled for you, which saves time. If you look on the very back you will see a little notch, and that is where your adjustment screw goes. It is pretty simple: slide it into that hole, and it seats onto the base of the bracket. That adjustment screw is what lets you aim the 4Banger up or down once everything is mounted. For the Silverado HD specifically, a dedicated bracket kit makes life easier, and you can reference the 20-23 Silverado HD 4Banger fog light bracket kit to see how these kits are laid out.

For our install we mounted the HXB wide and white pods, which are SAE compliant as we covered earlier. You route the 4Banger into the bracketry by taking the harness and placing the pod in. There are two little side holes on the pod, and the kit includes the hardware. Using a T30, you tighten those two screws down. Just make sure not to overtighten them, because you do not want to damage the bracket. Once the pod is secured, you plug in the Morimoto accessory harness. It plugs right into the 4Banger and makes the whole thing a full plug and play system.

Removing the OEM Fog Light on the Silverado HD

Down at the fender well, removing the factory fog light is the first real step on the truck. The first tool you need is a T15. Our test vehicle was modified and had two T15 screws, but on a standard setup you will only be removing one. Once that is out, pull back the fender liner and remove the 10 millimeter bolt on the back of your OEM fog light.

Removing the factory fog light starts with a T15 and a 10 millimeter socket at the fender well.

After the bolt is out, push on the three plastic clips on the back of the chrome bezel. That lets it move up and out of place. With the bezel free, wiggle the fog light and it will pop out. Once it is out, go ahead and disconnect the harness. That is all it takes to get the factory unit off the truck.

Installing the 4Banger Into the Truck

Before you install the 4Banger assembly, there are two plastic clips on the factory unit you need to move over. Remove those clips and slide them onto the very back of your 4Banger bracket. Next, slide the chrome bezel back into place and pull your OEM harness through so you can connect the 4Banger harness to it.

Feeding the 4Banger through the chrome bezel and locking it into place on the fog light face.

Now feed the Morimoto 4Banger through and into place. Line up those plastic clips carefully, then push directly on the 4Banger’s face, not the plastic bezel, to lock it into position. Pushing on the bezel instead of the pod face can throw off your seating, so this is one of those small details that makes the difference between a clean install and a fussy one.

Testing and Final Aim

With the fog light installed, test the product to make sure all functions are working properly before you close anything up. Once you confirm everything lights and functions correctly, take that 10 millimeter socket and reinstall the bolt where it was. Finally, make sure the fog light is aligned properly using that adjustment screw on the very back of the bracket. That aim screw you seated during the bracket build is what lets you dial the pod in for the best pattern on the road.

Testing the 4Banger for proper function and aim after final installation.

And just like that, your 4Banger fog light replacements are installed in your Silverado HD. Beyond the 2015 to 2019 Silverado HD, this fog light application fits a wide range of Chevy and GMC vehicles, including the 2007 to 2015 Avalanche, the 2010 to 2013 Camaro non RS, the 2007 to 2014 Suburban and Tahoe, the 2014 to 2015 Silverado 1500, the 2007 to 2018 Sonic, the 2015 to 2022 GMC Canyon, the 2007 to 2012 GMC Acadia, the 2014 to 2015 GMC Sierra 1500, the 2015 to 2018 GMC Sierra 2500, and the 2007 to 2014 GMC Yukon. If you are running any of those, this same install approach applies.

Our Takeaway

After running the full install, we can say the 4Banger delivers on the promise of a bright, compact pod light that fits cleanly into the factory fog location. The choice between NCS and HXB really comes down to your goals: the NCS is a strong entry point with the added bonus of a proper yellow chip if you want amber, while the HXB brings the Osram output for the folks who want the absolute top tier. Either way, the wide beam versions keep you SAE F3 compliant, the bracket kit makes install painless, and the limited lifetime warranty backs the whole thing up. For a Morimoto 4Banger fog light install on a Silverado HD, this is about as satisfying an upgrade as we have done.

Frequently Asked Questions

What is the difference between the NCS and HXB Morimoto 4Banger?

The NCS is the entry level version using a Nichia chip, while the HXB, also called HX Boost, is the premium version using an Osram chip aimed at off-roaders wanting the top tier pod light.

What beam patterns are offered for the Morimoto 4Banger?

Three patterns are available: a wide pattern for night visibility and fog light replacement, a combo pattern that is a spot beam with more fill, and a spot pattern that produces a tight, square beam.

Are the Morimoto 4Banger fog lights street legal?

Yes, both the NCS wide beam and the HXB wide beam models are designed to be compliant with the latest SAE F3 regulations for use as a street legal fog light.

Does the amber color option affect brightness?

Yes, on the HXB white light passing through the yellow lens loses about 30 percent of its brightness since it does not come in a yellow chip. The NCS uses yellow chips paired with a yellow lens, so its output stays closely matched to the white version.

What tools are needed to install the 4Banger on a 2015-2019 Silverado HD?

The install uses a T15 to remove the factory fog light, a 10 millimeter socket for the rear mounting bolt, and a T30 to secure the 4Banger into the Morimoto bracket.


Meet the Experts Behind Morimoto

Jimmy Engineering Manager at Morimoto Lighting

Jimmy Nguyen – Engineering Manager
Jimmy leads engineering at Morimoto, bringing experience across customer support, supplier management, design engineering, and validation testing. His work ensures Morimoto lighting systems are engineered for real-world reliability and long-term performance.

Mike Quality Control Manager at Morimoto Lighting

Mike Hicks – Quality Control Manager
Mike oversees quality assurance at Morimoto, with a background spanning returns testing, RMA analysis, vendor quality control, and manufacturer scorecards. His focus is continuous improvement and accountability across the product lifecycle.